【英文标准名称】:Safetyrequirementsforelectricalequipmentformeasurement,control,andlaboratoryuse-Part2-030:Particularrequirementsfortestingandmeasuringcircuits
【原文标准名称】:测量、控制和实验室用电气设备的安全性要求.第2-030部分:试验和测量电路的详细要求
【标准号】:IEC61010-2-030-2010
【标准状态】:现行
【国别】:国际
【发布日期】:2010-06
【实施或试行日期】:
【发布单位】:国际电工委员会(IX-IEC)
【起草单位】:IEC/TC66
【标准类型】:()
【标准水平】:()
【中文主题词】:电容器;防护等级;间隙;组件;接触安全装置;控制装置;控制设备;封盖物;定义;接地线端子;电气器具;电控制设备;电力系统;电气设备;电气工程;电学测量仪表;电阻;电气安全;电子工程;电子测量装置;熔断器;图形符号;冲击试验器;冲击试验;内爆;电感线圈;绝缘件;电离;实验室器皿;漏电;漏电路径;线路开关;处理;测量仪器;机械安全;计量学;微波;电动机;网络;插头和插座连接;插头;过程测量和控制设备;过程测量和控制技术;防电击;辐射;辐射防护;电阻器;回动杆;安全;安全措施;安全规则;安全要求;螺钉连接件;稳定;符号;温度;温升;试验指示计;试验;试验电压;热稳定性;超声压力;振动试验;电压;警告注释;警告符号
【英文主题词】:Capacitors;Classesofprotection;Clearances;Components;Contactsafetydevices;Controldevices;Controlequipment;Covers;Definitions;Earthingconductorterminations;Electricappliances;Electriccontrolequipment;Electricpowersystems;Electricalappliances;Electricalengineering;Electricalmeasuringinstruments;Electricalresistance;Electricalsafety;Electronicengineering;Electronicmeasuringdevices;Fuses;Graphicsymbols;Impacttesters;Impacttesting;Implosion;Inductancecoils;Insulations;Ionization;Laboratoryware;Leakagecurrent;Leakagepaths;Lineswitches;Marking;Measuringinstruments;Mechanicalsafety;Metrology;Microwaves;Motors;Network;Plug-and-socketconnection;Plugs;Processmeasuringandcontrolequipment;Processmeasuringandcontroltechnology;Protectionagainstelectricshocks;Radiation;Radiationprotection;Resistors;Reversinglevers;Safety;Safetymeasures;Safetyregulations;Safetyrequirements;Screwedjoints;Stabilization;Symbols;Temperature;Temperaturerises;Testfingers;Testing;Testingvoltages;Thermalstability;Ultrasonicpressure;Vibrationtests;Voltage;Warningnotes;Warningsymbols
【摘要】:ThispartofIEC61010specifiessafetyrequirementsfortestingandmeasuringcircuitswhichareconnectedfortestormeasurementpurposestodevicesorcircuitsoutsidethemeasurementequipmentitself.Theseincludemeasurementcircuitswhicharepartofelectricaltestandmeasurementequipment,laboratoryequipment,orprocesscontrolequipment.TheexistenceofthesecircuitsinequipmentrequiresadditionalprotectivemeansbetweenthecircuitandanOPERATOR.
【中国标准分类号】:N20
【国际标准分类号】:17_220_20;19_080;71_040_10
【页数】:66P;A4
【正文语种】:英语


Product Code:SAE J1521
Title:Truck Driver Shin-Knee Position for Clutch and Accelerator
Issuing Committee:Truck And Bus Human Factors Committee
Scope:This SAE Recommended Practice describes two-dimensional, 95th percentile truck driver, side view, seated shin-knee contours for both the accelerator operating leg and the clutch operating leg for horizontally adjustable seats (see Figure 1). There is one contour for the clutch shin-knee and one contour for the accelerator shin-knee. There are three locating equations for each curve to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.